Quick Answer: Whirlpool water softener error codes come in two groups. Err1, Err3 and Err4 point to the valve drive: the motor, the position switch, the wiring between them, or a valve so stiff the motor can't turn it. Err5 points to the electronic control board. For any of them, unplug the power supply, fix what you can see, plug it back in and wait 8 minutes. If the code comes back, the problem is still there and a part likely needs replacing.
Your Whirlpool is showing "Err" where the clock should be, and the buttons seem dead. That's normal for an error state, not a frozen control. Whirlpool water softener error codes lock out every button except PROGRAM while they're on screen; PROGRAM stays live so you (or a tech) can run the built-in diagnostics.
Sources: Whirlpool's Installation and Operation Manual for the WHES40 and WHES44 (Rev. A 1/24/23), and the WHES3T manual (document 7385299, Rev. C). Other Whirlpool models may differ, so check the model sticker under the salt lid and pull your own manual from Whirlpool Water Solutions' product manuals page.
In this guide
- What Whirlpool water softener error codes mean in the manual
- Clear the code with the 8-minute reset test
- Narrow down Err1, Err3 or Err4 before buying parts
- Err5 points at the control board
- Run a manual regeneration check afterward
- When a new softener beats another repair
- FAQ
- Reset once, then fix what the code keeps pointing to
What Whirlpool water softener error codes mean in the manual

The WHES40/WHES44 troubleshooting guide groups the codes like this:
| Code on display | Possible cause listed by Whirlpool | Fix listed by Whirlpool |
|---|---|---|
| Err1, Err3 or Err4 | Fault in the wiring harness or connections to the position switch | Replace the wiring harness or connections |
| Err1, Err3 or Err4 | Fault in the switch | Replace the switch |
| Err1, Err3 or Err4 | Fault in the valve causing high torque | Replace the rotor/seal |
| Err1, Err3 or Err4 | Motor inoperative | Replace the motor |
| Err5 | Electronic control malfunction | Replace the electronic control board |
The manual doesn't tie Err1, Err3 and Err4 to one specific part each. In practice, all three mean the control told the valve to move and didn't get the position switch signal it expected. The cause could be electrical (harness, switch, motor) or mechanical (a valve too stiff to turn). A little diagnosis before buying parts pays off.
The WHES3T manual doesn't print a code list. It describes an automatic self-diagnostic for the electrical system (except input power and the water meter), says an error code appears if a malfunction occurs, and gives the customer line, 1-866-986-3223, for help. Have your model and serial number from the rating decal ready when you call.
Clear the code with the 8-minute reset test

Whirlpool's procedure for removing an error code doubles as a test:
- Unplug the transformer from the outlet.
- Correct the problem.
- Plug the transformer back in.
- Wait 8 minutes.
The manual says plainly that the error code will return if the problem wasn't corrected. If the clock comes back and stays, you're in business. Reset the time of day if it's flashing; our guide on how to program a Whirlpool water softener covers the settings.
A one-off error after a storm or a tripped breaker that clears on the first try usually isn't worth chasing. A code that returns every time is.
Narrow down Err1, Err3 or Err4 before buying parts

Work from free to expensive:
1. Check the plug, outlet and transformer. Make sure the outlet isn't on a wall switch or a tripped GFCI. A weak or intermittent supply can stop the motor mid-move.
2. Look at the harness connections. With the unit unplugged, lift the salt lid and remove the top cover (the WHES3T cover unlocks at the back tabs and rocks forward). Check where the wires meet the position switch and the control. A connector that's half off, a pinched wire or green corrosion from a damp spot is the cheapest fix you'll find.
3. Run Manual Advance Diagnostics. On the WHES3T, press and hold PROGRAM for 3 seconds until "000" appears, then release. Use RECHARGE to advance the valve into each cycle while you watch the cam and switch with the cover off. If the motor turns and the cam moves to each position, the drive is probably fine. If the motor hums but the cam doesn't move, or nothing happens at all, you've found the area of the fault.
4. Think about the valve itself. Whirlpool lists "fault in valve causing high torque" with the rotor/seal as the fix. Sediment, iron or scale can make the rotor hard to turn, especially on well water. If your water carries iron or sand, this is a strong suspect.
5. Switch or motor last. A dead motor is possible, but replace it only after the cheaper checks. Our motor not turning guide walks through how to tell a failed motor from a stuck valve.
Err5 points at the control board

Err5 is the one code Whirlpool ties to a single part: the electronic control board. Do the unplug-and-wait reset once, since a power glitch can upset a control temporarily. If Err5 returns, replacement is the fix the manual gives.
Before ordering, write down your full model and serial number. Boards are model-specific, and the control also stores a model code: the WHES3T manual's diagnostic screen lets you check and change that code if it doesn't match the unit. A new board usually needs the model code, clock, hardness and recharge time entered before it runs correctly.
Run a manual regeneration check afterward

Once the code clears, make sure the valve can complete a full cycle. The WHES3T manual includes a Manual Advance Regeneration Check, done with a steady (not flashing) clock on screen:
- Press and hold RECHARGE for 3 seconds. The valve moves to fill. Remove the brinewell cover and shine a flashlight in to confirm water is coming in.
- Press RECHARGE to move to brine. The brine level should drop noticeably; the manual says this can take 15 to 20 minutes. Make sure the water is touching the salt and not sitting under a salt bridge.
- Press RECHARGE to move to backwash. Look for a fast flow out of the drain hose.
- Press RECHARGE to move to fast rinse and let it run a few minutes to flush out brine.
- Press RECHARGE to return to service.
If the code reappears partway through, note which step it was on. That helps a service tech, or a parts counter, narrow things down fast.
When a new softener beats another repair
A harness, switch or motor is a reasonable repair. A board plus a rotor and seal on an older unit starts to approach the price of a new softener. If you're weighing replacement, our GE vs Whirlpool water softener comparison and WaterBoss vs Whirlpool breakdown look at what you get from each brand's current lineup.
Always unplug the softener before removing the cover. If the outlet shows signs of moisture or scorching, call an electrician before troubleshooting the softener.
FAQ
Why won't any buttons work on my Whirlpool softener?
While an error code is on the display, Whirlpool locks out every button except PROGRAM. That's by design, so a service person can enter the diagnostics. Clear the code with the unplug-and-wait-8-minutes procedure to get normal control back.
Does a blank screen mean the same thing as an error code?
No. A blank display usually means no power is reaching the control: a tripped GFCI, a failed transformer or a loose plug. Our error code or blank display guide covers that case.
Can I keep using water while the error code is showing?
Usually yes, because an error stops regeneration, not water flow. But the resin won't recharge, so the water will turn hard once the capacity is used up. Put the softener in bypass if the valve is leaking or stuck in a drain cycle.
Will I lose my settings when I unplug it?
How much a Whirlpool control remembers depends on the model, so check the display after the 8-minute wait. If the time is flashing, set it again, then confirm hardness and recharge time while you're in the menus.
What does Err2 mean on a Whirlpool softener?
Whirlpool's WHES40/WHES44 troubleshooting table doesn't list an Err2. If you see a code that isn't in your model's manual, call Whirlpool's line at 1-866-986-3223 with the model and serial number.
Reset once, then fix what the code keeps pointing to
Most Whirlpool water softener error codes come down to two questions: does the valve drive move and report its position (Err1, Err3, Err4), and is the control board healthy (Err5)? Unplug, fix what you can see, plug in and wait 8 minutes. If the code returns, work from power and harness to rotor, switch and motor, and save the board for an Err5 that won't clear. Then run a manual regeneration check so you know the repair actually took.
