Quick Answer: Fleck 5600 mechanical timer setup takes four moves. Hold the red time-set button and turn the 24-hour gear until the current time sits at the time-of-day arrow. On a time-clock model, slide skipper wheel tabs outward for each night you want it to regenerate (the tab at the red pointer is tonight). On a metered model, set the program wheel. To regenerate now, turn the manual regeneration knob slowly clockwise until the micro switch lifts.
No screen, no buttons, just a dial and a ring of little tabs. Fleck 5600 mechanical timer setup is simple once you know which wheel does what, but nothing on the faceplate tells you. The mechanical 5600 is one of the most common softener valves ever sold, and plenty are still running decades later.
This walkthrough follows Pentair's Fleck 5600 Service Manual (document 40106 Rev K), which covers both the time-clock and metered versions. A copy is hosted on InspectApedia. If you have the digital 5600SXT with an LCD screen and three buttons, this isn't your page. See how to program a Fleck 5600SXT instead.
In this guide
- Time clock or meter: which Fleck 5600 timer is on your tank?
- Set the clock with the red button and 24-hour gear
- Skipper wheel tabs decide which nights it regenerates
- Programming the meter wheel on a demand 5600
- Fleck 5600 mechanical timer setup on a new or rebuilt valve
- Turning the manual regeneration knob without stripping the drive
- Timer motor dead? Check these before buying a new head
- Set the clock right and the tabs do the rest
- FAQ
Time clock or meter: which Fleck 5600 timer is on your tank?

Pull the front cover off and look at the timer.
- Time clock (calendar) version: a 24-hour gear plus a small skipper wheel with tabs around its edge. It regenerates on the nights you choose, whether you used water or not. Pentair sells this head as a 5600 electromechanical time clock in 7-day and 12-day versions, so count the tabs before you plan a schedule.
- Meter version: a 24-hour gear plus a program wheel marked in gallons, often with a "people" dial and a hardness scale, and a meter cable running down to the valve body. It counts water and regenerates when the gallons run out.
Both share the same red button, 24-hour gear and manual regeneration knob, so the clock and knob steps below apply to either.
Set the clock with the red button and 24-hour gear

Press and hold the red time-set button. This disengages the drive so the big gear can turn freely. Turn the 24-hour gear until the current time sits at the "time of day" arrow, then release the button.
What you'll see: the gear spins easily with the button held and locks when you let go. If it won't turn even with the button pressed, don't force it. Pentair's own spec describes heavy-duty 3/8-inch plastic gears, and plastic teeth are exactly what breaks when you lean on them.
Get AM and PM right. It's a 24-hour gear, so 7 in the morning and 7 at night sit on opposite sides of the dial. A clock set 12 hours off means the softener regenerates in the middle of the afternoon while you're running water.
Shifting the regeneration hour with a clock offset
The mechanical timer starts regeneration at a fixed point on the dial, usually marked on the gear itself (2:30 a.m. on many units, but check yours). You can't move that trip point, but you can shift the clock. To regenerate at 4:30 a.m. instead, set the clock two hours behind real time. The dial then reaches its trip point two real hours later. Write the offset on tape inside the cover, or the next person will "fix" your clock. Our guide to what time a water softener should regenerate explains why the small hours are the usual choice.
Daylight saving time and power cuts
The clock doesn't know about daylight saving time, so twice a year move it an hour, as explained in our daylight saving time guide. A mechanical timer also stops dead during an outage and resumes from where it stopped, so the manual's fix for a power failure is simply to reset the time of day.
Skipper wheel tabs decide which nights it regenerates

Per the manual: slide tabs on the skipper wheel outward to expose the trip fingers. Each tab is one day. An exposed finger means "regenerate that night." The finger at the red pointer is tonight. Moving clockwise from the red pointer, extend or retract fingers to build the schedule you want.
Worked example: how many nights to pick
Say you have three people, water at 15 grains per gallon, and an older 1 cubic foot softener that delivers roughly 24,000 grains at its salt setting.
- Water use: 3 people × 75 gallons a day = 225 gallons a day. (75 gallons per person is the same figure Fleck's manual uses for reserve.)
- Hardness load: 225 × 15 = 3,375 grains a day.
- Days until the resin runs out: 24,000 ÷ 3,375 ≈ 7 days.
You never want to run it to empty, so regenerate well before that. Every third or fourth day is a safe choice here: pull out two tabs with a gap between them, like Sunday and Wednesday. If your hardness is higher or the household bigger, add a night. Don't know your hardness? Test it at home first. Our regeneration frequency guide runs this math for more situations, and if you don't know your resin's real capacity, how to size a water softener shows how to estimate it.
Programming the meter wheel on a demand 5600

The meter version needs to know how many gallons it can soften before regenerating. The manual gives two ways.
The people dial (typical residential). Lift the "people" dial and rotate it so the number of people in the household lines up with your water hardness in grains per gallon on the scale. Release it and check that it seats firmly. This method builds in reserve at 75 gallons per person.
Gallons at the white dot (optional method). Work out the gallons yourself and set them at the small white dot on the program wheel gear:
- Divide softener capacity in grains by hardness in gpg. A 24,000-grain softener on 15 gpg water gives 1,600 gallons.
- Subtract the reserve: people × 75. For three people, that's 225.
- Set roughly 1,375 gallons at the white dot.
As water is used, the program wheel turns counterclockwise until it reaches the regeneration position. The manual says each tooth-to-tooth step of the small gear on the front of the timer is about 30 gallons, which is handy for checking that the meter is actually moving. Run a measured amount of water and watch.
If the program wheel never moves while water is running, pull the meter cable out of the meter cover and turn it by hand. The wheel should move without binding and the clutch should click when it hits the regeneration stop. If that works but it still won't track water use, the meter is the problem; if the wheel binds, the timer is.
Fleck 5600 mechanical timer setup on a new or rebuilt valve

A fresh install, a rebuilt piston or a softener that sat drained all winter needs the full start-up, not just a clock setting. Condensed from the manual's softener procedure:
- Before plugging in, turn the knob to In Service and let water fill the resin tank slowly. When flow stops, open a softened-water tap until the air is out, then close it.
- Turn the knob to Backwash and let water run to drain for 3 or 4 minutes.
- Check the salt setting behind the back cover matches the manufacturer's recommendation, then index to Brine Fill and let the brine tank fill to the top of the air check.
- Index to Brine Draw and let it draw until it stops.
- Plug in and look through the sight hole on the back of the motor to confirm it's turning. Set the skipper tabs (or program wheel) and the time of day.
- Advance to the start of Brine Fill and let the control return to In Service on its own.
- Add salt, replace the cover and make sure any bypass is in the normal service position.
The manual also warns against granulated or rock salt in the brine tank. Use pellets or crystals.
Turning the manual regeneration knob without stripping the drive

Use this after setup, after running out of salt, or any time you want to check the valve. Turn the manual regeneration knob slowly clockwise until the program micro switch lifts onto the first set of pins. The motor then takes over and drives through backwash, brine and slow rinse, rapid rinse and brine tank refill, then returns to service.
If you're stepping through cycles by hand, the manual's rule is simple: always let the motor stop before moving to the next set of pins or spaces. Forcing the knob while the motor runs is how people strip the drive.
Stay nearby for the first few minutes. You should hear water rushing to the drain during backwash. If you don't, check the drain line before blaming the timer.
Timer motor dead? Check these before buying a new head
The manual's troubleshooting table points to the same few causes when a 5600 won't regenerate on schedule:
- No power: check the fuse, plug, pull chain or switch feeding the outlet.
- Power failure: the clock stopped; reset the time of day.
- Defective timer: if power is present and the motor in the sight hole isn't turning, replace the timer motor or timer assembly.
- Control cycles nonstop or drain runs continuously: a faulty or jammed timer mechanism, or debris and worn seals in the valve body.
Parts for the old 5600 are still easy to find, but a lot of owners use a dead timer as the excuse to upgrade the control head. Our guide to replacement water softener control valves covers bolt-on options, and if the tank and resin are also tired, our picks for the best Fleck water softeners include complete systems on the same 5600 platform with a digital meter.
Set the clock right and the tabs do the rest
Fleck 5600 mechanical timer setup comes down to three settings that rarely change: the time of day (with any offset written down), the nights on the skipper wheel or the gallons on the meter wheel, and a test regeneration with the knob to prove the motor and drain work. Recheck the clock after every outage and at each daylight saving change, and revisit the tabs only if your household or water hardness changes.
FAQ
How do I set the time on a Fleck 5600 mechanical timer?
Press and hold the red time-set button, turn the large 24-hour gear until the current time is at the time-of-day arrow, and release the button. Make sure you've chosen the correct AM or PM side of the dial.
What time does a mechanical Fleck 5600 regenerate?
It regenerates when the 24-hour gear reaches a fixed trip point, which is 2:30 a.m. on many units. Check the marking on your gear. To change the real-world time, set the clock ahead or behind by the difference.
How many skipper wheel tabs should be pulled out?
One tab per regeneration night. Divide your softener's grain capacity by your daily hardness load (people × 75 gallons × grains per gallon) and regenerate comfortably before that many days pass. For many small households that means two or three tabs a week.
Why didn't my Fleck 5600 regenerate last night?
The usual causes are a clock stopped by a power cut, a clock set 12 hours off, no tab pulled out for that night, or a timer motor that has stopped. Check the time of day first, then look through the sight hole on the back of the motor to see if it's turning.
Can I convert a mechanical 5600 to a digital 5600SXT?
Often, yes. Upgrade heads that put a digital control on a 5600 valve body are sold, but confirm compatibility with your valve and part numbers before ordering. Many owners swap the whole head rather than replace an old timer motor.
