Quick Answer: Fleck 7000SXT error codes run from Err 0 to Err 3, plus UD. Err 2 (Regen Failure) means no regeneration in over 99 days (7 on Day-of-Week setups): hold Extra Cycle for 5 seconds to regenerate and clear it, then check that the meter counts flow. Err 0 means the drive took over 6 minutes to reach the next position. Err 1 is a switch or settings mismatch, Err 3 is board memory, and a stuck UD or blank screen is fixed by draining the super capacitor.
A 7000SXT softener can run "fine" for months, then someone notices water spots and an error on the display. That timeline points to one specific code, and it's the most fixable one.
Everything here comes from the troubleshooting section of Pentair's Fleck 7000SXT Service Manual (document 42775). Error codes appear on the In Service display, where the time normally shows. The 7000 is Fleck's larger, higher-flow valve; the 7000 series spec sheet lists it on a 24 VAC supply, which matters for the blank-screen check below.
In this guide
- Fleck 7000SXT error codes and what triggers each
- Error 2 on a metered 7000SXT: the meter stopped counting
- Error 0 and Error 1: drive, switches and settings
- Stuck on UD or a blank screen? Drain the super capacitor
- Error 3 and the two 7000SXT resets
- Most 7000SXT errors are fixed at the meter, the piston or the reset button
- FAQ
Fleck 7000SXT error codes and what triggers each
| Code | Fleck's name | Trigger in the manual | First step |
|---|---|---|---|
| Err 0 | Cam Sense Error | Drive took over 6 minutes to reach the next regeneration position | Unplug; check cam switches, motor, gears, piston |
| Err 1 | Cycle Step Error | Unexpected cycle input | Check cam switches; confirm valve and system type |
| Err 2 | Regen Failure | No regeneration in over 99 days (7 if Day-of-Week) | Manual regeneration; check meter and settings |
| Err 3 | Memory Error | Control board memory failure | Master Reset and reprogram |
| UD | Upper Drive Sync | Power failure or programming change | Should recover by itself |
| Blank | No display / backlight only | Power failure | Check the 24 VAC transformer |
The numbered codes match the 5600SXT, since both use SXT-family electronics. Our Fleck 5600SXT error codes guide covers that valve. What the 7000SXT manual adds is extra recovery advice for UD and a dead screen.
Error 2 on a metered 7000SXT: the meter stopped counting

Many 7000SXT softeners are metered: they regenerate when they've counted enough gallons. If the meter stops counting, the control believes nobody is using water. It never reaches capacity, never regenerates, and after 99 days Err 2 appears. Meanwhile the resin has been exhausted for weeks.
Clear it. The manual says to perform a manual regeneration to reset the code. Hold Extra Cycle for 5 seconds. Let it run all the way through, since exhausted resin needs the full brine contact time.
Fix the cause, in the manual's order:
- Is it measuring flow? Run softened water and watch the display. The flow indicator flashes when outlet flow is detected.
- If not, check the meter cable at both ends.
- Then the meter itself. A turbine jammed by debris won't spin. Our meter not counting guide covers cleaning and testing it.
- Then the settings. In Master Programming, confirm system capacity, day override and meter type. On a Day-of-Week system, make sure at least one day is ON.
A day override is your backstop: even if the meter fails, the unit regenerates at least every so many days. If yours was set to off, turn it on.
Error 0 and Error 1: drive, switches and settings

Err 0 (Cam Sense) means something is dragging or something isn't reporting. Unplug the unit and take the cover off the powerhead, then:
- Cam switches: verify each is connected to the circuit board and working.
- Motor and drive train: confirm they're in good shape and assembled properly. A stripped or misaligned gear stalls the drive. To sort a dead motor from a jammed valve, see softener motor not turning.
- Piston: it must travel freely. On well water with iron or grit, a piston sticking in its seals is a common cause; our stuck piston guide covers removing it. Bypass the softener first.
- Plug back in and watch. The unit should cycle to the next valve position and stop. If Err 0 returns, Fleck says to contact technical support.
Err 1 (Cycle Step) is about confusion, not speed. Inspect the cam switches, then confirm in Master Programming that the valve type and system type match your unit. This matters after a board replacement: the 7000's default valve type is standard downflow with double backwash, so a softener built differently will misbehave on defaults. Finish by stepping through a manual regeneration. During it, the display shows B1, BD, B2, RR and BF (first backwash, brine draw, second backwash, rapid rinse, brine fill).
Stuck on UD or a blank screen? Drain the super capacitor

UD normally clears by itself after a power failure or programming change. If it doesn't, the manual says to check that the motor is turning the gears:
- Gears not moving: you likely have a jammed piston or a drive motor that needs replacing.
- Gears moving: drain the super capacitor. Unplug the unit, press the reset button on the circuit board, and plug it back in. The display should be restored.
A blank display, or backlight only, gets a similar treatment. First check that the transformer is putting out 24 volts AC. If it is, drain the super capacitor the same way. If the transformer reads nothing, replace it. Our error code or blank display guide covers outlet and wiring checks for any brand.
Error 3 and the two 7000SXT resets

For Err 3, the manual's path is a Master Reset (hold Extra Cycle while powering up the unit), then reconfigure everything in Master Programming and run a manual regeneration. If the error comes back, contact technical support; the board is likely failing.
The manual also describes a Soft Reset: hold Extra Cycle and Down for 25 seconds in service. It returns parameters to defaults but keeps the volume remaining (metered) or days since regeneration (time clock).
Both wipe your programming. Photograph or write down capacity, regeneration time, cycle times and meter settings first. If you don't have the original job specification sheet, the manual includes one to fill in.
Power outages alone shouldn't cause an error. The SXT keeps time and day count for at least 48 hours without power and stores the remaining volume. It doesn't count water used during the outage, and a long outage can leave the clock wrong, so check the time even when no code shows.
Most 7000SXT errors are fixed at the meter, the piston or the reset button
Read Fleck 7000SXT error codes in that order: Err 2 is almost always the meter or a missing day override, Err 0 and Err 1 live in the switches, gears, piston or valve-type setting, and UD or a blank screen usually clears with a super capacitor drain. Cam switches, motors and boards are sold individually. But if the powerhead has a long fault history or the valve body is worn, a new head may be less hassle: see our best replacement control valves, or best Fleck water softeners for complete systems.
FAQ
How do I clear Error 2 on a Fleck 7000SXT?
Hold the Extra Cycle button for 5 seconds to start a manual regeneration, which resets the code. Then open a softened tap and confirm the flow indicator flashes. If it doesn't, the meter or its cable is the real problem.
What is UD on a Fleck 7000SXT display?
UD is Upper Drive Sync. It appears after a power failure or a programming change while the drive finds its position, and it should clear on its own. If it doesn't, check that the motor turns the gears, then drain the super capacitor with the reset button on the circuit board.
Why is my Fleck 7000SXT screen blank?
The manual lists power failure as the cause. Check the outlet, then confirm the transformer outputs 24 volts AC. If it does, unplug the unit, press the reset button on the circuit board to drain the super capacitor, and plug it back in.
How do I reset a Fleck 7000SXT?
For a Soft Reset, hold Extra Cycle and Down for 25 seconds while in service. For a Master Reset, hold Extra Cycle while plugging the unit in. Both erase settings, so record them first.
Are Fleck 7000SXT error codes the same as the 5600SXT?
The numbered codes Err 0 to Err 3 and UD have the same names and triggers on both. The 7000SXT manual adds recovery steps for a stuck UD and a blank display that involve the 24 VAC transformer and the circuit board reset button.
