WaterBoss Error Codes E1 to E5: What Each Means and How to Fix It

Quick Answer: WaterBoss error codes on the 700, 900 and 950 run from E1 to E5. E1 (home not found) and E3 (home offset) usually mean the controller isn't pushed fully onto the drive end cap: reseat it and unplug the transformer, then plug it back in. E2 is a motor error, so check the motor plug. E4 (home latched) points to gears or a jam. E5 is a memory error that needs a new controller.

WaterBoss error codes are refreshingly specific. Three of the five are about "home," the starting position the controller uses to track the valve disk. When it can't find home, starts somewhere else, or gets latched there, you see E1, E3 or E4, and the usual cause is mechanical and easy to see.

Everything below comes from the troubleshooting table in the WaterBoss 700, 900 and 950 owner's manual (version 7.9, pages 31–32). An earlier version 7.3 of the same manual lists the same codes. If you have a different model, check its own manual.

In this guide
  1. What the five WaterBoss error codes mean
  2. Reseat the controller for E1 and E3
  3. E2 means check the motor plug first
  4. E4 that returns after a reset
  5. E5: replace and reprogram the controller
  6. A blank display: heat or power, not a code
  7. FAQ
  8. Repair the WaterBoss, or price a replacement

What the five WaterBoss error codes mean

Diagram of the home position on a WaterBoss valve disk and how E1, E3 and E4 relate to it
CodeNameWhat the manual says to do
E1Home not foundUnplug the transformer and plug it back in; it looks for home again. Push the controller fully onto the drive end cap
E2Motor errorPlug the motor in and cycle power. If it's already plugged in, the motor wiring or plug is defective
E3Home offsetThe disk didn't start at home. The controller tries to reset itself and continue the regeneration. Push the controller fully on
E4Home latchedGear teeth aren't engaged, a gear is stripped, or something is jammed. Cycle power to reset
E5Memory errorReplace the controller

Cycling power on a WaterBoss means unplugging the low-voltage transformer, not flipping a breaker. The unit runs on 12 VAC from that plug-in transformer.

Reseat the controller for E1 and E3

Diagram comparing a WaterBoss controller fully seated on the drive end cap with one left with a gap

Two of the five codes carry the same instruction: push the controller all the way onto the drive end cap. It can get nudged during salt refills, while cleaning around the unit, or after someone pulls it off to reach the valve. The manual gives the same fix when the softener stays stuck in regeneration.

  1. Unplug the transformer.
  2. Look at the joint between the controller and the drive end cap. Any gap, tilt or play is a problem.
  3. Press the controller straight on until it's fully seated. Don't force it at an angle.
  4. Plug the transformer back in and watch the display.

For E3, the controller tries to recover on its own by finding home and carrying on with the regeneration. Give it a few minutes before deciding the code is stuck. If E1 keeps returning with a well-seated controller, the drive and gears are the next suspects.

E2 means check the motor plug first

Flowchart for a WaterBoss E2 motor error: unplug, reseat the motor plug, restore power, then decide

E2 is the "is it plugged in?" code. Unplug the transformer, find the motor's connector and make sure it's firmly in place, then restore power. If the motor was already connected and E2 comes back, the manual says the motor wiring or motor plug is defective, which is a parts job. Our motor not turning guide covers what else can stop a softener motor.

E4 that returns after a reset

Diagram of meshed drive gears next to a stripped gear that causes a WaterBoss E4 home latched error

The manual's first step for E4 is a power cycle, and it's worth trying. But look at the causes: gear teeth not engaged, a stripped gear, or something jammed in the valve. A reset can help if the teeth slip back into mesh. It won't fix a stripped gear or a jam.

If E4 returns:

  • Put the softener in bypass and unplug the transformer.
  • Remove the controller and look at the drive gear teeth. Chipped or rounded teeth mean a replacement gear.
  • If the gears look fine, the valve may be jammed. The manual lists a foreign object in the main control valve as a cause of stuck regeneration too. On well water, sediment or iron is a common suspect. Clearing it means opening the valve, which you may prefer to leave to a dealer.

E5: replace and reprogram the controller

E5 is a memory error, and the manual gives only one fix: replace the controller. There's no reset. Once the new controller is on, program it again with the time of day, your water hardness and any other settings. Our guide on how to program a WaterBoss walks through the four-button menus.

A blank display: heat or power, not a code

Four-step checklist for a blank WaterBoss display: temperature, transformer and outlet, 12 VAC test, then the controller

No read-out at all isn't one of the error codes, but the manual covers it:

  • Heat. If the room temperature exceeds 120°F (49°C), the display blanks out. The manual says this doesn't affect the controller and no action is needed. That matters for units in a hot garage, attic or closet next to a water heater.
  • Power. Check that the transformer is plugged in and that the outlet isn't controlled by a wall switch.
  • Transformer. Test for 12 VAC at the controller with a voltmeter. Under 10 VAC, replace the transformer.
  • Controller. If 12 VAC is present and the display is still blank, replace the controller.

Heat that high is outside the unit's rated 40°F to 120°F range anyway, so shade or relocate it if it happens often. Our blank display guide covers other brands.

FAQ

How do I reset a WaterBoss error code?

Unplug the transformer, wait a moment and plug it back in. That clears E1, E3 and many E4 codes once the cause is fixed. Reseat the controller on the drive end cap first, since that's the manual's fix for E1 and E3.

What does E1 mean on a WaterBoss water softener?

E1 means home not found: the controller can't locate the valve disk's starting position. Push the controller fully onto the drive end cap, then cycle power so it looks for home again.

What does E2 mean on a WaterBoss 900?

E2 is a motor error. Make sure the motor is plugged in and cycle power. If it was already plugged in, the manual says the motor wiring or motor plug is defective.

Why is my WaterBoss display blank?

Either it's above 120°F where the unit sits, which blanks the display without affecting operation, or it has lost power. Check the transformer, the outlet and the 12 VAC supply before replacing the controller.

Who do I call about WaterBoss error codes?

The manual lists the WaterBoss HelpLine at 1-800-437-8993, 8 a.m. to 5 p.m. EST. Have your manual and the unit's serial number ready.

Repair the WaterBoss, or price a replacement

Most WaterBoss error codes come down to a loose controller, a loose motor plug or a worn gear, all approachable DIY repairs on a compact unit. If an older softener needs a new controller and a drive gear at the same time, compare that cost with a new unit using our WaterBoss vs Whirlpool comparison and our picks for the best water softeners for small homes. Always unplug before removing the controller, and bypass the softener before opening the valve.