Pentair Water Softener Error Codes, Sorted by the Valve You Actually Have

Quick Answer: Pentair water softener error codes depend on the control valve on top of the tank. A Fleck 5600SXT shows 0, 1, 2, 3 or UD. An Autotrol 742/762 shows ERR 1, ERR 2, ERR 3 or four dashes. An Autotrol Logix 764 adds ERR 4 for a second tank. Most clear once the cause is fixed, with a power cycle, a button press or a manual regeneration. A memory fault (Fleck code 3) needs a master reset and full reprogramming.

Searching "Pentair water softener error codes" gives mixed answers because Pentair doesn't make a single control. It owns Fleck and Autotrol, two of the most common valve brands in US homes, and its name ends up on systems built around both. A code 3 on a Fleck means something completely different from ERR 3 on an Autotrol.

So read the label on the valve head, not the tank. Every code below comes from Pentair's own manuals.

In this guide
  1. Which Pentair control is on your tank?
  2. Fleck 5600SXT codes on Pentair systems
  3. What do Autotrol 742 and 762 ERR codes mean?
  4. Logix 764 adds ERR 4 for twin tanks
  5. Pentair water softener error codes after a power outage
  6. Force a regeneration to prove the fix
  7. Board, motor or the whole softener?
  8. FAQ
  9. Read the valve label, then trust Pentair's code list

Which Pentair control is on your tank?

Diagram comparing the Fleck 5600SXT, Autotrol 742/762 and Logix 764 keypads and the error codes each one uses
  • Fleck 5600SXT: a small LCD with three buttons, Extra Cycle, Up and Down. "Fleck" and "5600SXT" are printed on the cover or a side sticker.
  • Fleck 2510SXT or 7000SXT: the same three-button keypad on a bigger valve body. Their codes differ slightly, so use our Fleck 2510SXT error code guide or the Fleck 7000SXT error codes page.
  • Autotrol 742 or 762: an Autotrol logo, buttons labeled SET, REGEN, UP and DOWN, and an hourglass icon that shows while the motor runs.
  • Autotrol Logix 764: the same four buttons, with "764" on the label. It can run twin-tank systems, which is where its extra code comes from.

Fleck 5600SXT codes on Pentair systems

Flowchart for Fleck code 2: check whether the flow indicator flashes, then fix the meter or the programming and run a manual regeneration

These come from Pentair's 5600SXT Softener System manual (document 4005293). The code appears on the in-service display.

CodeWhat the manual saysWhat to do
0: Cam sense errorThe valve drive took longer than 6 minutes to reach the next regeneration position.Unplug, check the cam switches are connected, the motor and gears are intact and the piston moves freely. Plug back in: the valve should step to the next position and stop.
1: Cycle step errorThe control got an unexpected cycle input.Check the cam switches, then confirm valve type and system type in Master Programming. Step through a manual regen.
2: Regen failureNo regeneration for more than 99 days (7 days on a day-of-week setup).Run a manual regeneration, which resets the code. Then find out why it stopped regenerating.
3: Memory errorControl board memory failure.Master reset, reprogram, then step through a manual regen. If it returns, the board is failing.
UD: Upper drive syncA power failure or programming change.Nothing. The valve recovers on its own.

Code 2 is rarely a hardware fault. If the meter cable is loose or the turbine is stuck, the softener never sees water use, so it never triggers a regen and eventually flags it. Open a tap and watch for the flashing flow indicator; our guide to a water softener meter not counting walks through the fixes. If flow registers, check capacity, the day override and, on day-of-week controls, that at least one day is set ON.

Soft reset vs master reset on the SXT

The manual lists two resets, and they're not the same:

  • Soft reset: hold Extra Cycle and Down for 25 seconds in normal service. It returns settings to defaults but keeps the remaining volume or days since the last regen.
  • Master reset: hold Extra Cycle while plugging the unit in. It clears everything, so you must go back through Master Programming.

Photograph every setting before either one. We cover the menus in how to program a Fleck 5600SXT, and our dedicated Fleck 5600SXT error codes page goes deeper on each code.

What do Autotrol 742 and 762 ERR codes mean?

Decision path for Autotrol ERR 3: wait two minutes for the camshaft to find Home, then check the motor, harness, optical sensor and cam slots

These are from Pentair's 742/762 control manual (P/N 3001093).

DisplayMeaningHow to clear
ERR 1The controller lost track of its operating state.Press UP. The control should reset.
ERR 2Power frequency doesn't match. The North American controller runs on 60 Hz and won't work on 50 Hz.Unplug and reconnect. If it persists, you need the controller or AC adapter rated for your supply.
ERR 3The controller doesn't know where the camshaft is, so it turns it to find Home.Wait. Within two minutes the hourglass should flash, and the code clears at Home.
— — : — —A power failure occurred.Press SET and reset the time.

ERR 3 usually means the controller is finding its place after a power blip. The manual treats it as a real fault in two cases:

  • The camshaft isn't turning. Check the motor plug, the wire harness, the optical sensor and that the motor gear meshes with the cam gear.
  • It turns for more than five minutes. Check that the optical sensor is seated, the camshaft is connected and no debris sits in the cam slots.

If the motor itself is dead, our motor-not-turning guide covers the checks for both brands.

Resetting an Autotrol 742/762

This returns the control to an unprogrammed state:

  1. Hold SET and DOWN together for 5 seconds.
  2. You'll see H0 with the resin volume (or "F" mode). If another history value shows, press UP until H0 appears.
  3. Hold SET for 5 seconds.
  4. Reprogram the control as if it were new.

Logix 764 adds ERR 4 for twin tanks

The Logix 764 owner's manual uses a shorter list:

  • ERR 1: program settings are corrupted. Press any key and reprogram the Level I settings.
  • ERR 3: the controller on tank 1 is finding the camshaft's Home position. The checks match the 742/762 above. If ERR 3 appears partway through a regeneration, confirm the right valve type is selected in the controller.
  • ERR 4: the same homing problem on tank 2. On a single-tank system, ERR 4 means the system setting is wrong; the manual says to set it to 293/298 "L".

Pentair water softener error codes after a power outage

Lantern glowing by a rain-streaked window during a storm, when power cuts can leave a softener showing a reset code

Storms cause more of these codes than broken parts do. What you see depends on the valve:

  • Fleck 5600SXT: UD after power returns. Leave it alone. The manual says programming is stored in permanent memory, so no backup battery is needed.
  • Autotrol 742/762: four dashes, sometimes followed by ERR 3 while the camshaft homes. Pentair warns that outages longer than 8 hours can lose the time and day settings, so check the clock even if no code shows.

The 742/762 manual also says to keep the adapter off a switched outlet.

Force a regeneration to prove the fix

Diagram of the regeneration steps on a Fleck 5600SXT (BW, BD, RR, BF) and an Autotrol 742/762 (C1 to C8)

A cleared code doesn't prove the valve works. Run a regeneration and watch it.

  • Fleck 5600SXT: hold Extra Cycle for 5 seconds for an immediate regen. A single press queues one for the next regen time and flashes the service icon. Our Fleck 5600SXT manual regeneration guide shows how to step through each cycle.
  • Autotrol 742/762: hold REGEN for 5 seconds for an immediate regen (solid symbol). A single press delays it until the regen time, 2:00 AM by default (flashing symbol).

Look for steady drain flow during backwash, the brine level dropping during draw, and refill at the end. If the code returns mid-cycle, note which step it stopped on.

Board, motor or the whole softener?

Hand choosing a screwdriver from a toolbox before opening a softener control head

Fleck and Autotrol controllers, motors and optical sensors are sold as separate parts. Swapping one is a reasonable repair on a tank that's otherwise healthy, and our list of the best replacement control valves covers full heads. If the resin is old, the tank is weeping or you're on your second board, read repair or replace an old water softener first.

Shopping for a new system? Start with our Pentair water softener review, the Pentair vs Culligan comparison or the best Fleck water softeners.

FAQ

What does ERR 3 mean on a Pentair water softener?

It depends on the valve. On an Autotrol 742, 762 or Logix 764, ERR 3 means the controller is rotating the camshaft to find its Home position, usually after a power interruption, and it should clear within a couple of minutes. On a Fleck 5600SXT, code 3 is a control board memory failure that needs a master reset and reprogramming.

How do I reset a Pentair water softener?

On a Fleck 5600SXT, hold Extra Cycle and Down for 25 seconds for a soft reset, or hold Extra Cycle while plugging it in for a master reset. On an Autotrol 742/762, hold SET and DOWN for 5 seconds, make sure H0 shows, then hold SET for 5 seconds. Both wipe settings, so photograph them first.

Why does my Pentair softener show code 2?

The Fleck 5600SXT shows code 2 when it hasn't regenerated in more than 99 days, or 7 days on a day-of-week setup. A manual regeneration clears it. The usual cause is a meter that isn't counting water, so check the flow indicator and meter cable before blaming the board.

Will a power outage cause an error code?

Often, yes. A Fleck SXT shows UD and recovers on its own. An Autotrol 742/762 shows dashes until you reset the time, and may show ERR 3 while it re-homes the camshaft. Outages longer than 8 hours can also wipe the Autotrol's time and day settings.

Can I replace just the controller on a Pentair softener?

Yes. Fleck and Autotrol controllers, motors and sensors are sold as replacement parts. Pentair's ERR 3 troubleshooting lists the harness, motor and optical sensor before the controller, so try the cheaper parts first.

Read the valve label, then trust Pentair's code list

Pentair water softener error codes only make sense once you know whether a Fleck or an Autotrol head is doing the work. Match the keypad, look up the code in that valve's table, fix the cause, then run a full regeneration to prove it. A code that keeps returning after a reset points at the board, motor or sensor, all of which are replaceable.